Annovi Reverberi AR RTX Series Repair And Maintenance Video

Annovi Reverberi AR RTX series repair and maintenance video the on models RTX30, RTX50, RTX60, RTX70, RTX85 and RTX100 piston triplex plunger pumps. In this video, the AR North America technical team will be showing you do repair and maintenance step by step.

Find the RTX pumps breakouts here:
RTX Breakouts
See replacement RTX pumps here:
RTX Catalog
Service Dealers (buy parts here):
http://goo.gl/e3KcqD

This video will cover how to replace the Inlet and discharge valves along with the pistons, seals and guides on any RTX series pump.

Here are the kits and their parts numbers needed to service the pump
The kits may vary depending on which pump you have

To replace the 6 inlet and discharge valves on this pump, remove the valve caps on the manifold with a 32mm socket

Next, using a pair of needle nose or valve pliers remove the valves by grabbing the plastic valve cage while twisting and pulling straight out

Note that the inlet and the discharge valves are different on this pump , the discharge vales on the top have a black spring and the inlet valves on the bottem have a silver spring.

Make sure to clean the thread sealer off of the plugs and the ports for your valves to prevent damage when reassembling it

Put in the new valves in their correct spot and make sure they are properly seated

Its ok to use something that you have a firm grip on and that will not damage the inside of your pump to make sure they are in all the way

Apply a thin layer of thread sealer all the way around the threads when reinstalling the valve caps

Make sure to torque the caps to 3540 Inch pounds or 295 foot pounds before the adhesive dries

Never use the airgun when re-assembling your machine because this can lead to injury to you or damage to your pump

To access the pistons and their guides start by removing the 8 head bolts with a 8 MM allen socket.

To take off the head, rotate the crankshaft with a wrench or your hand if you can

This allows enough space to evenly pry off the head with 2 screwdrivers on opposite side of the pump

After that, support the bottom of the head and push off with your thumbs

Be careful not to apply too much pressure to one side of the head because this can crack the ceramic pistons

Once the manifold is off there will be parts either on the pistons or still in the head of the machine.

To remove parts off of the pistons start by using a wrench or your hand to rotate the crankshaft, this will push the parts towards the end of the piston making them easier to twist off.

To take the rear piston guide and low pressure seal assembly out of the head the best method is to use a pair of channel lock pliers to twist and pull them out

Next take out the front piston guide

If you cant take out the low pressure seal out by hand, use a small flathead screwdriver to pry parts out without scratching the inside of the pump.

The first item to go into the manifold will be the head rings with the flat side facing down
Next comes the high pressure seal, its concave side should fit over the support ring
New seals are tough to fit in, make sure to work them in at an angle and to only use your hands
The rear support ring should then fit on top of that
The front piston guide comes next with its curved side going into the head
To put the rear piston guide in start by replacing the o ring on the outside, then place in the brown backup ring into it
The low pressure seal goes on top of the backup ring with the bumpy side sticking out of the guide

If the guide is put in squarely it should click into place

To replace the pistons, remove the piston bolt using a 13mm socket.

Again, make sure to clean off any thread sealant from the bolts before putting them back in

If you are not replacing the pistons make sure to scrape off any residue that has accumulated on the outside
Once they have been thoroughly cleaned you can put the copper plate and the piston back on

apply a small amount of threadlocker all the way around the bottom on the piston bolt before retightening them

Torque the piston bolt to 62 inch pounds

To properly put on the manifold turn the crankshaft so that the outer pistons are even
This helps with pushing the head back on squarely

New seals may be tight, so you can use a soft faced hammer to evenly tap it into place while supporting it

These head bolts should be torqued to 442 inch pounds or 37 foot pounds

Torquing in a criss cross manner can help evenly tighten the head onto the pump

Annovi Reverberi AR RGX series repair and maintenance video

Annovi Reverberi AR RGX series

Annovi Reverberi AR RGX series repair and maintenance video the on models RGX2250HN and RGX1550HN piston triplex plunger pumps. In this video, the AR North America technical team will be showing you do repair and maintenance step by step.

0:20 Discharge Valves
1:57 Inlet Valves
3:49 Water Seals & Piston Guides
6:59 Pistons

Find the RGX pumps breakouts here:
http://www.arnorthamerica.com/pages/p…
Buy replacement RGX pumps here:
http://www.arnorthamerica.com/categor…
Service Dealers (buy parts here):
http://goo.gl/e3KcqD

This video will cover how to replace the Inlet and discharge valves along with the pistons, guides and seals on any Annovi Reverberi AR RGX series pump.

These are the tools used in the video to repair the machine

Here are the kits and their parts numbers needed to service the pump

To replace the 3 discharge valves on the top of this pump, remove the valve caps on the manifold with a 24mm socket

There are 6 valves in total, the other 3 require the head bolts to be taken off

Next, using a pair of needle nose or valve pliers remove the valves by grabbing the plastic valve cage while twisting and pulling straight out

Make sure to clean the thread sealer off of the plugs and the ports for your valves to prevent damage when reassembling it

Put in the new valves and use something that will not damage the inside of your pump to properly seat them

Apply a thin layer of thread sealer all the way around the threads when reinstalling the valve caps

Make sure to torque the caps to 531 Inch pounds or 44 foot pounds before the adhesive dries

Never use the airgun when re-assembling your machine because this can lead to injury to you or damage to your pump

To access the remaining valves, pistons, guides and their seals start by removing the 8 head bolts with a 8 MM allen socket.

The inlet manifold should come off with the head bolts

There are several ways to remove the inlet valves with the first being a 12MM bolt, whos threads match up with the valves

Next is a pair of valve pliers

Third is the reverse pliers, where you twist and pull to take the valve out.

Use a pick to take out the old o rings near the bottoms of the valves

Watch out for this small o ring that may fall out, without it. Your pump will end up leaking.

Put in the new o rings, followed by the new inlet valve

To get to the pistons, seals and their guides, we need to remove the head of the pump
The best way to remove the it is to support the bottom while tapping the top with a soft face mallet.

Do this until there is enough room to evenly pry off the head with 2 screwdrivers on opposite side of the pump

Be careful not to apply too much pressure to one side of the head because this can crack the ceramic pistons

Once the manifold is off there will be parts either on the pistons or still in the head of the machine.

To take out parts still in the head you can use a rear piston guide extractor, which we sell on our website.

After that, Take out the front piston guide by hand
A small flathead screwdriver can be used to pry out the high pressure seal if it can’t be taken out with your fingers.

To remove parts off of the pistons start by using a wrench or your hand to rotate the crankshaft, this will push the parts towards the end of the piston making them easier to twist off.

The first item to go into the manifold will be the head rings with the flat side facing down
Next comes the high pressure seal, its concave side should fit over the support ring
New seals are tough to fit in, make sure to work them in at an angle and to only use your hands
The brown backup ring should then fit on top of that
The front piston guide comes next with the angled side going into the head
To put the rear piston guide in start by replacing the o ring on the outside, then place in the low pressure seal with the flat side first into the guide
Put a small amount of grease onto the support ring so that it stays in the seal when putting in the head

When properly seated it should click into place

To replace the pistons, remove the piston bolt using a 10mm socket.

Again, make sure to clean off any thread sealant from the bolts before putting them back in

Now you can replace the brass plate, followed by the new piston

Add the copper washer to the piston bolt along with applying a thin layer of thread sealer all the way around the threads before retightening them

Torque the piston bolt to 62 inch pounds

Now we can place the manifold back onto the pistons and reapply the head bolts

To properly put on the manifold turn the crankshaft so that the outer pistons are even
This helps with pushing the head back on squarely

New seals may be tight, so you can use a soft faced hammer to evenly tap it into place while supporting it

These head bolts should be torqued to 442 inch pounds or 37 foot pounds

Video Overview Of Annovi Reverberi

We are excited to share a new video overview of Annovi Reverberi. You might just know us as AR North America but we are 1/3 of Annovi Reverberi founded in 1958 in Modena, in the heart of the Italian engineering district.

This video will give an overview of our presence in five continents and more than a hundred countries with a network of manufacturing and commercial facilities which allow a direct presence in local markets, in a strategy of total focus on the needs of end customers. We believe it will give you the confidence that our process and products are industry leading.

Contact us if you would like more information on how we can help you realize the power of our experience.

Announcing the Annovi Reverberi RGX Plunger Pump Series

Annovi Reverberi RGX series pump

AR North America is excited to announce the Annovi Reverberi RGX Plunger Pump Series. The RGX pump series is a solid shaft 24mm pump runs at 1,450 RPM and delivers 4 to 5.8 GPM and 7250 PSI. The RGX has a new-design head with the intake valves placed above the pistons to generate higher-than-normal pressures. This new head configuration also simplifies valve maintenance even without intake plugs. The pump features one-piece ceramic pistons and a double gasket sealing system.

The Annovi Reverberi Manufacturing Process

Like most companies, we manufacture some of our Annovi Reverberi high pressure pumps in China. We took our time to find the right team to introduce the AR process and techniques to reflect our traditions.  AR as a company has 59 years of manufacturing experience. The company started to Italy and has since grown to offer products worldwide.  This video highlights or team in China.

Please don’t hesitate to contact us if you are looking for the highest quality pumps when quality matters.

Bolondi High Pressure Cleaning Heads

Bolondi Cleaning HeadAR North America is proud to be an official distributor of Bolondi cleaning heads and washing nozzles. Just like Annovi Reverberi, Bolondi is located in Italy. In fact it’s only minutes from our headquarters in Modena.

We believe Bolondi makes the highest quality cleaning heads available. Food, wine, spirits, beer, pharmaceuticals, cosmetics, chemical, car washes, drum cleaning, bin cleaning, sanitation and more. They are the perfect combination with an Annovi Reverberi high pressure plunger pump.

The most popular Bolondi cleaning head is the BISW060. Self-spinning washing head for containers open on one side. Reduce water consumption by not washing an area of 120° wide at the base of the spray head keeping spray in the container. Spinning speed of 120 g/min. Water Motor.

If you are looking for a car wash nozzle we recommend the BIPW060. Self-rotating cleaning head working at a set, constant rotating speed. Ideal for underbody washing systems. Variable arm length. 2 – 3 – 4 nozzles. Water Motor.

If you have a cleaning nozzle we suggest you start with the best in Bolondi. Visit our online catalog page featuring all of our Bolondi cleaning heads or contact us today for a conversation and quote.